Multi-line 2 AGC-4 Mk II Application Software
You’re about to download Multi-line 2 AGC-4 Mk II Application Software
You have chosen to download our software.
Within a few seconds, you will receive an email containing a download link.
Having trouble using the software? Please contact support@deif.com.
Best regards,
DEIF A/S
The software is subject to copyright DEIF A/S
By following the above mentioned link and downloading the file you automatically accept DEIF A/S copyright and license agreement (EULA). The license agreement can be found on www.deif.com/software
This software applies to the following DEIF products:
You’re about to download 6.21.0
The main changes implemented since the last version are as follows:
- USW version required: 3.62.0
- TDU version required: 1.4.5.0
PM compatibility: 1.41.0
New features
- EIC: Added many new SPN texts for DM1 log.
- EIC: Added fuel rate alarm based on active power.
- GENSET: Added counter for number of successful generator starts.
- EIC: Added Guascor GCS-e ECU protocol.
Changes
- M-Logic: Renamed 'Virtual toggle' to 'Virtual event' and 'Virtual switch' to 'Virtual toggle'.
- Virtual events work the same on Modbus and M-Logic. The output of the virtual event will follow the input of the virtual event.
- Virtual toggles work the same on Modbus and M-Logic. If the input of the virtual toggle goes high, the output changes state once.
- Added parameter 7075, "Mains Fail Assumption", which enables the Mains controller to assume that the mains have just recovered at start-up, allowing it to run the OK timers.
- EIC: Keyswitch (#15050) is available for J1939 protocols.
- Updated EODev H2G fuel cell transmission rate has been to 20 ms for I, P and Q measurements.
- EIC: Added TSC1 to YC-ECU-A.
- EIC: Changed crankcase pressure (SPN 101) to kPa unit in delta alarms.
Corrections
- GENSET: The frequency/voltage regulation mode is no longer dependent on the frequency detection level when running with the GB closed.
- GENSET: Gen stop + GB Off M-Logic command can now stop the genset during the start sequence.
- If breaker is not used, the associated position feedback are cleared so they can be used for something else. Also added protection against overwriting position feedback assignment when the associated breaker is setup.
- M-Logic virtual toggles (previously named switches) can now be read over Modbus.
- GENSET: If idle run was active, RMI oil pressure alarms would be active before it was detected that the engine was running. This has been changed so that the engine must be running before the alarms can be active.
- Droop curve 2 configured with power factor output now works properly again.
- GENSET: Regulation mode will correctly be set to fixed power P/Q control when PMS isochronous master is active in power management.
Ver. | Date | Description |
---|---|---|
6.21.0 |
19/05/2025 |
PM compatibility: 1.41.0 New features
Changes
Corrections
|
6.20.0 |
10/03/2025 |
PM compatibility: 1.40.0 New features
Changes
Corrections
|
6.15.1 |
07/02/2025 |
PM compatibility: 1.35.1 Corrections
|
6.15.0 |
03/12/2024 |
USW version required: 3.61.0 PM compatibility: 1.35.1 New features
Changes
Corrections
|
6.14.0 |
27/09/2024 |
IMPORTANT: This software requires USW-3 version 3.60.2 with PDB revision 10901 or higher. PM compatibility: 1.35.1 New features:
Changes:
Corrections:
|
6.13.1 |
15/07/2024 |
PM compatibility: 1.34.0 Corrections1- Corrected unit restarting if Profibus option is selected. |
6.13.0 |
18/06/2024 |
PM compatibility: 1.34.0 New features 1- Fuel optimisation further optimised in more applications, including PV and battery. Changes 1- Spinning reserve stop hysteresis calculation is now based on the nominal power on busbar after next DG to stop.
Corrections 1- Auto calculation multistarts with fuel optimisation, now works before the TB is closed. |
6.12.1 |
26/02/2024 |
PM compatibility: 1.34.0 Corrections
|
6.12.0 |
30/10/2023 |
PM compatibility: 1.32.0 New features• EIC: Added support of Weichai E6. Changes• EIC: Added GTACP (0xFE05, SPN2452/2460) to Caterpillar generic and Perkins generic. Corrections• PMS priority update in 32DG application now working correctly. |
6.11.3 |
21/09/2023 |
PM compatibility: 1.30.1 Corrections
|
6.11.2 |
14/09/2023 |
PM compatibility: 1.30.1 Corrections
|
6.11.1 |
21/07/2023 |
PM compatibility: 1.30.0 Corrections
|
6.11.0 |
11/07/2023 |
PM compatibility: 1.30.0 New features
Changes
Corrections
|
6.10.2 |
25/05/2023 |
PM compatibility: 1.29.0 Corrections
|
6.10.1 |
23/03/2023 |
PM compatibility: 1.29.0 Corrections
|
6.10.0 |
06/03/2023 |
PM compatibility: 1.29.0 New features
Changes
Corrections
|
6.09.1 |
20/01/2023 |
PM compatibility: 1.29.0 Corrections
|
6.09.0 |
23/12/2022 |
PM compatibility: 1.28.0 New features:
Changes:
Corrections:
|
6.08.1 |
13/12/2022 |
PM compatibility: 1.28.0 Corrections:
|
6.08.0 |
17/11/2022 |
PM compatibility: 1.28.0 New features:
Changes:
Corrections:
|
6.07.0 |
11/07/2022 |
PM compatibility: 1.25.0 New features:
Corrections:
|
6.06.0 |
18/02/2022 |
PMS compatibility: 1.25.0 New features: Finetuning: |
6.05.0 |
01/02/2022 |
PM compatibility: 1.24.2 New features:
Changes:
Corrections:
|
6.04.3 |
16/11/2021 |
PM compatibility: 1.24.1 Corrections:
|
6.04.2 |
10/11/2021 |
PM compatibility: 1.24.1 Corrections:
|
6.04.1 |
22/10/2021 |
Not UL approved version PM compatibility: 1.24.1 Corrections:
|
6.04.0 |
07/10/2021 |
Not UL approved version PM compatibility: 1.24.1 New features:
Changes:
Corrections:
|
6.03.1 |
13/09/2021 |
Not UL approved version PM compatibility: 1.24.1
|
6.03.0 |
15/07/2021 |
Not UL approved version PM compatibility: 1.24.1 New features:
Changes:
Corrections:
|
6.02.1 |
06/05/2021 |
UL approved version PM compatibility: 1.23.0 Corrections:
|
6.02.0 |
06/04/2021 |
Not UL approved version PM compatibility: 1.23.0 New features:
Changes:
Corrections:
|
6.01.2 |
15/03/2021 |
Not UL approved version PM compatibility: 1.22.0 Corrections:
|
6.01.1 |
12/02/2021 |
Not UL approved version PM compatibility: 1.22.0 Corrections:
|
6.01.0 |
11/01/2021 |
UL approved version PM compatibility: 1.22.0 New features:
|
6-00-0 |
07/01/2021 |
Not UL approved version PM compatibility: 1.22.0 |