Multi-line 2 AGC 150 Application Software
You’re about to download Multi-line 2 AGC 150 Application Software
You have chosen to download our software.
Within a few seconds, you will receive an email containing a download link.
Having trouble using the software? Please contact support@deif.com.
Best regards,
DEIF A/S
The software is subject to copyright DEIF A/S
By following the above mentioned link and downloading the file you automatically accept DEIF A/S copyright and license agreement (EULA). The license agreement can be found on www.deif.com/software
This software applies to the following DEIF products:
- AGC 150 Hybrid - Advanced Genset Controller
- AGC 150 Engine Drive - AGC 150 Engine Drive
- AGC 150 Remote Display - Remote access and control unit
- AGC 150 Generator - Advanced Genset Controller
- AGC 150 BTB - Advanced Genset Controller
- AGC 150 Mains - Advanced Genset Controller
- AGC 150 Stand alone - Advanced Genset Controller
You’re about to download 1.11.0
The main changes implemented since the last version are as follows:
PM compatibility: 1.25.0
New features:
- JC15D Weifu alarm texts added to DM1 log.
- Added support of JC15D WYS EIC protocol.
- Added support of JC190 EIC protocol.
- Added support of Bosch EDC17CV54TMTL EIC protocol.
- Added configurable TSC1 transmission rate and checksum/counter for Generic J1939.
- Added support of Xichai EIC protocol.
- Enable/disable alarm ack. via J1939 (DM11).
- Added support of Kubota EIC protocol.
- Extended RMI 20 Points in multi-inputs.
- Extended mA 17 Points in multi-inputs.
- Hybrid Supervision view on controller display added.
- Parameter to block nominal settings changed.
- Extended EIC wait to start (preheat) support. Introduced M-Logic command to inhibit wait to start.
- View line: Added kW per phase (L1, L2, L3).
- View line: Added kW per phase in percent (L1, L2, L3).
- View line: Added Power factor per phase (L1, L2, L3).
- EIC: Added support of Scania EMS2 S8 HC Evaporation Status in M-logic and view.
- View line: Added Charge Alternator Voltage - D plus voltage.
- Automatic speed detection view line.
- Automatic oil pressure view line.
- Automatic water temperature view line.
- Automatic fuel level detection view line.
- Multi-input view lines change text with RMI selected.
- Added RMI Custom to multi-input input type.
Changes:
- J1939 protocol "Jichai" renamed to "JC15D Weifu".
- FPT/Iveco Stage V updated.
- Default views updated.
- Default values for multi-input.
Corrections:
- N + X ON/OFF via digital input or M-Logic corrected.
- Busbar measurement working correct in single and split phase with BB set to 3W3.
- A genset will now charge a battery with the correct amount during negative PMS set points.
- A genset will now calculate the correct power reference if a battery operating as a energy source is charging from excess PV power.
- A running DG with its GB closed could react to invalid power management data when changing from a single DG application to a standard application.
- DVC 550/D550: Stator current limitation events in M-Logic did not work.
- A mains could issue a start signal to DGs based on invalid power management data when a BTB was power cycled.
- AOP-2 button emulation from USW-3 working.
- Fault in PDB. Alarm Relay ND and NE text swap. I/O setup is wrong; parameter is correct.
- External generator breaker configuration on DGs corrected so GB relays are configurable.
- Configuration of running detection timer is now working from display.
Ver. | Date | Description |
---|---|---|
1.11.0 |
11/07/2022 |
PM compatibility: 1.25.0 New features:
Changes:
Corrections:
|
1.10.4 |
30/06/2022 |
PM compatibility: 1.25.0 Corrections:
|
1.10.3 |
01/06/2022 |
PM compatibility: 1.25.0 Corrections:
|
1.10.2 |
19/04/2022 |
PM compatibility: 1.25.0 Corrections:
|
1.10.1 |
18/03/2022 |
PM compatibility: 1.25.0 Corrections:
|
1.10.0 |
28/02/2022 |
PM compatibility: 1.25.0 New features:
Changes:
Corrections:
|
1.09.1 |
08/02/2022 |
PM compatibility: 1.24.2 Corrections:
|
1.09.0 |
14/12/2021 |
PM compatibility: 1.24.2 New features:
Changes:
Corrections:
|
1.08.1 |
01/12/2021 |
PM compatibility: 1.24.2 Corrections:
|
1.08.0 |
11/11/2021 |
PM compatibility: 1.24.2 New features:
Changes:
Corrections:
|
1.07.0 |
21/06/2021 |
PM compatibility: 1.24.1. New features:
Changes:
Corrections:
|
1.06.1 |
06/05/2021 |
Version 1.06.1 based on 1.06.0. PM compatibility: 1.23.0. Corrections:
|
1.06.0 |
29/04/2021 |
PM compatibility: 1.23.0. New features:
Changes:
Corrections:
|
1.05.4 |
06/04/2021 |
PM compatibility: 1.22.0. Corrections:
|
1.05.3 |
02/03/2021 |
PM compatibility: 1.22.0. Corrections:
|
1.05.2 |
06/01/2021 |
PM compatibility: 1.22.0. Corrections:
|
1.05.1 |
08/12/2020 |
PM compatibility: 1.22.0. Corrections:
|
1-05-0 |
30/11/2020 |
PM compatibility: 1.22.0. New features:
Changes:
Corrections:
|
1-04-2 |
22/09/2020 |
PM compatibility: 1.17.2. Corrections:
|
1-04-1 |
29/07/2020 |
Version 1.04.1 based on 1.04.0 Corrections:
|
1.03.1 |
14/05/2020 |
PM compatibility: 1.17.2. Corrections:
|
1.03.0 |
03/04/2020 |
PM compatibility: 1.17.2 New features:
Changes:
Corrections:
|
1.02.0 |
26/03/2020 |
PM compatibility: 1.17.0. New features:
Changes:
Corrections:
|
1.01.0 |
19/12/2019 |
PM compatibility: 1.17.0. New features:
Corrections:
|
1.00.3 |
22/10/2019 |
PM compatibility: 1.17.0 Corrections:
|
1.00.2 |
05/08/2019 |
Version 1.00.2 based on 1.00.1 Corrections:
|
1.00.0 |
30/04/2019 |
PM compatibility: 1.17.0
|
On this page, you can download software updates for your product(s) and help yourself to various utility tools and add-ons that will assist you in setting up, detecting faults and configuring your product(s).
Please be advised that not all of our products can be updated by the user. Nor do all of our products come with a utility tool. Consequently, the list on this page cannot be considered an overview of our product programme.
DEIF will register your download along with the used e-mail address for the purpose of sending out information on future updates, if requested.
DEIF cannot be made responsible for any consequences of failed product updates or use of utility tools. Nor can DEIF A/S be made responsible for consequences of changes in behaviour of products due to a software upgrade. It is always the responsibility of the user to ensure correct set-up and configuration before commissioning. Please study the version log of the software before updating the product.
Licence agreement for software downloaded from www.deif.com
Downloaded software remains the property of DEIF. The software may not be distributed for commercial purposes, changed or reused in full or in part or sold to any third parties.
The latest versions for full functionality
As always, we recommend that you install our offered improvements to fully utilise your DEIF product.
All improved software can be downloaded at your convenience at www.deif.com under “Software”.
Should you have any questions or experience problems finding the relevant software for your product, please feel free to call DEIF A/S at +45 96149614 or your relevant local DEIF office. Alternatively, we are always ready to assist you, if you send an e-mail to support@deif.com.