iE 350 Marine application SW (Protection & Paralleling) 2.0.9.0

You’re about to download iE 350 Marine application SW (Protection & Paralleling) 2.0.9.0

You have chosen to download our software.

Within a few seconds, you will receive an email containing a download link.

Having trouble using the software? Please contact our support and create a ticket. 

Best regards, 

DEIF A/S

The software is subject to copyright DEIF A/S
By following the above mentioned link and downloading the file you automatically accept DEIF A/S copyright and license agreement (EULA). The license agreement can be found on www.deif.com/software

You’re about to download 2.0.9.0

The main changes implemented since the last version are as follows:

2.0.9.0 based on 2.0.8.1

New features

  • Three pump logic routines can now be set up to control the pumping of a substance.
  • Implement ECU diagnostic to enable run coil and ECU power while the engine is stopped.
  • All configuration dependent values are now possible to use in the flexible Modbus.  

Changes

  • Number of possible Modbus connections changed from 20 to 100 on iE 250 and iE 350.
  • Modbus timeout increased from 10 sec to 100 sec on iE 250 and iE 350. 
  • Added write permission for "Priorities" when the controller is in emulation.
  • EIC: Volvo Penta EMS2.4: "Engine Override Control Mode" changed to "Speed control".  
  • EIC: Volvo Penta EMS2.4: TSC1 will not be transmitted if VP70 is used for regulation.   

Corrections

  • Fixed issue where changes made in the UI were not registered.
  • Fixed issue where the "IO configuration" menu would show empty slots.
  • Fixed issue where tree-structure menu groups could not be collapsed using touch.
  • Fixed issue where configuring a Modbus value to "true" made the value "255" instead of "1".
  • Fixed issue where measurements from multiple ECUs were not shown in the UI for e.g. configuring alarms.
  • Fixed issue where the display user could not clear DM2 logs.
  • Fixed issue where the iE controller could not start without MIO module.
  • Fixed issue with missing alarm icons.
  • Fixed issue where the user could enter parameter values outside of the valid range.
  • Fixed checksum and counter for VP70.
  • Fixed issue where removing the network cable would activate system NOK, IO service error and "temperature too high" alarms. 
  • Fixed issue where CODESYS user management files were not included in backup/restore.
  • Fixed issue where linked outputs in CODESYS were hidden in IO configuration.
Ver. Date Description

2.0.9.0

04/05/2025

2.0.9.0 based on 2.0.8.1

New features

  • Three pump logic routines can now be set up to control the pumping of a substance.
  • Implement ECU diagnostic to enable run coil and ECU power while the engine is stopped.
  • All configuration dependent values are now possible to use in the flexible Modbus.  

Changes

  • Number of possible Modbus connections changed from 20 to 100 on iE 250 and iE 350.
  • Modbus timeout increased from 10 sec to 100 sec on iE 250 and iE 350. 
  • Added write permission for "Priorities" when the controller is in emulation.
  • EIC: Volvo Penta EMS2.4: "Engine Override Control Mode" changed to "Speed control".  
  • EIC: Volvo Penta EMS2.4: TSC1 will not be transmitted if VP70 is used for regulation.   

Corrections

  • Fixed issue where changes made in the UI were not registered.
  • Fixed issue where the "IO configuration" menu would show empty slots.
  • Fixed issue where tree-structure menu groups could not be collapsed using touch.
  • Fixed issue where configuring a Modbus value to "true" made the value "255" instead of "1".
  • Fixed issue where measurements from multiple ECUs were not shown in the UI for e.g. configuring alarms.
  • Fixed issue where the display user could not clear DM2 logs.
  • Fixed issue where the iE controller could not start without MIO module.
  • Fixed issue with missing alarm icons.
  • Fixed issue where the user could enter parameter values outside of the valid range.
  • Fixed checksum and counter for VP70.
  • Fixed issue where removing the network cable would activate system NOK, IO service error and "temperature too high" alarms. 
  • Fixed issue where CODESYS user management files were not included in backup/restore.
  • Fixed issue where linked outputs in CODESYS were hidden in IO configuration.
Ver. Date Description

2.0.16.2

04/03/2026

Corrections

  • Fixed an issue where restoring an older backup on version 2.0.15.0 or newer prevented logging in to the controller from the CODESYS IDE.
  • Fixed an issue where it was not possible to select imperial units on the controller.
  • Fixed an issue that allowed the controller variant check to be overridden during backup restoration.
  • Fixed an issue where backups over 50 MB could not be restored to the controller.
  • Fixed an issue where it was not possible to log in to the controller after a factory reset.
  • EIC: Fixed missing SAE J1939 SPN texts for DM1 and DM2 alarms.
  • EIC: Fixed missing measurement for engine oil-filter differential pressure.

2.0.16.1

13/02/2026

Correction

  • Fixed an issue that caused the controller to restart if the user did not take action.

2.0.16.0

29/01/2026

Version 2.0.16.0 (based on version 2.0.15.0)

New feature

  • EtherCAT® performance improvements, enhancing communication between PCM3.3, modules, and extension racks.

Corrections

  • Fixed an issue with the display header.
  • Fixed an issue with GAM3.2 regulation.

Version 2.0.15.0 (based on version 2.0.14.1)

New features

  • EIC: Added John Deere Stage V protocol.
  • Added Engine heater logic.
  • Added 16 analogue ICC values. These values are global, meaning all controllers can read and write to each of the 16 values.
  • Added the possibility to restore a different variant when the controller is not part of a plant.

Corrections

  • Resolved an issue where the NTP server connection status intermittently failed to update, resulting in false alarms indicating no NTP servers were connected even when servers were actively synchronised. The system now correctly detects and reports NTP server status, including proper handling of transient connection states during normal NTP operation.
  • Added proprietary DEF level reading for Scania EMS2 S8 and Isuzu protocols.
  • Added missing alarm output from PMS network monitoring.
  • Resolved an issue where NTP could not be configured in PICUS.
  • Fixed the possibility to change brightness level.
  • Fixed an issue with backup to PICUS where the controller displayed an error.

Version 2.0.14.1 (based on version 2.0.14.0)

Corrections

  • Fixed authentication issue.

Version 2.0.14.0 (based on version 2.0.13.0)

Changes

  • Architectural updates in preparation for new power management.

Corrections

  • Fixed an issue where the bootloader was not updating correctly.
  • Fixed an issue that prevented IOM3.2 or IOM3.3 from operating, causing a System Not OK alarm.
  • Fixed an issue with GAM3.2 configuration when in stand-alone mode for analogue regulation.
  • Fixed an issue with synchronisation visualisation.
  • Fixed an issue where permissions were missing after a backup/restore cycle.
  • Fixed an issue affecting the performance of analogue regulation on the analogue bidirectional I/O terminals.
  • Fixed an issue with the logout message in WebConfig.
  • Fixed an issue with the new password error in User Management.
  • Fixed an issue where spurious information was occupying log entries, making it harder to see valid entries.
  • Fixed an issue where Chinese characters were not displayed correctly.

2.0.13.0

16/10/2025

New features

  • Added new average system frequency measurement.

Corrections

  • Added event log entry when time settings are changed.
  • Alarm timestamps are now only updated when being acknowledged.
  • Alarms are no longer sorted by last interaction.
  • iE250: Fixed issue where a custom name for an I/O on the controller would also name an I/O on an IOM3.1 module.
  • Fixed issue where the CustomTexts JSON endpoint returned inaccurate responses and corrected data format for POST.
  • Changed custom logic so the CB configuration failure alarm does not appear.
  • Fixed issue where Directional Overcurrent 1 and 2 were not enabled after power cycle if set point values were negative.
  • It is now possible to map both digital and analogue inputs/outputs to Modbus addresses, across all ranges of iEx50.
  • Corrected timing for transmission of CAN telegrams.
  • Fixed an issue where the 'Module update required' pop-up was not triggered as expected.

2.0.11.2

11/08/2025

Corrections

  • Fixed issue where it was not possible to back up and restore user management

2.0.11.1

08/07/2025

New features

  • Increased maximum delay time on all single-measurement alarms such as frequency, voltage, power, current, over and under alarms.

Corrections

  • Fixed an issue where entries on DM2Logs were missing text.
  • IOM3.2: Fixed an issue where PWM output was not usable. It can now be enabled with a fixed frequency and voltage on AO1 and AO2.
  • Fixed an issue where the display command drop-down list contained duplicate entries.
  • iE 250: Fixed an issue where the connection to the extension rack was lost when both the plug-in module and the extension rack were connected.
  • Fixed an issue where the Eventlog had missing text and missing attributes.
  • iE 250: Fixed an issue where the "Fieldbus connection missing" alarm was triggered even when the connections were OK.
  • Fixed an issue where it was not possible to set Port mode to RSTP External.
  • Fixed an issue where using external breaker feedbacks could cause incorrect power management behaviour.
  • Fixed an issue where external and redundant breaker feedback could result in an incorrect breaker position state.
  • Dynamic Section Status is now available again in CODESYS Development System.

2.0.10.1

27/06/2025

[2.0.10.1] - 2025-06-18

New minor release with improvement in installation process.  

New features

  • Introduced iE BSP v1.0.0.0, including GetDiskFree, GetPCMSerialNumber and ReadOSVersion

Changes

  • Increased MaxChannels to 8 for the ChannelServer
  • Removed support for CODESYS runtimes v3.5.18.40, PCM2.1, PCM3.3 and PCM6.2
  • Updated DEIF_SysUtil_PCM61 to v1.0.0.1, added selection of terminations for CAN ports
  • Removed Debug entries from StdLogger.csv

2.0.9.0

04/05/2025

2.0.9.0 based on 2.0.8.1

New features

  • Three pump logic routines can now be set up to control the pumping of a substance.
  • Implement ECU diagnostic to enable run coil and ECU power while the engine is stopped.
  • All configuration dependent values are now possible to use in the flexible Modbus.  

Changes

  • Number of possible Modbus connections changed from 20 to 100 on iE 250 and iE 350.
  • Modbus timeout increased from 10 sec to 100 sec on iE 250 and iE 350. 
  • Added write permission for "Priorities" when the controller is in emulation.
  • EIC: Volvo Penta EMS2.4: "Engine Override Control Mode" changed to "Speed control".  
  • EIC: Volvo Penta EMS2.4: TSC1 will not be transmitted if VP70 is used for regulation.   

Corrections

  • Fixed issue where changes made in the UI were not registered.
  • Fixed issue where the "IO configuration" menu would show empty slots.
  • Fixed issue where tree-structure menu groups could not be collapsed using touch.
  • Fixed issue where configuring a Modbus value to "true" made the value "255" instead of "1".
  • Fixed issue where measurements from multiple ECUs were not shown in the UI for e.g. configuring alarms.
  • Fixed issue where the display user could not clear DM2 logs.
  • Fixed issue where the iE controller could not start without MIO module.
  • Fixed issue with missing alarm icons.
  • Fixed issue where the user could enter parameter values outside of the valid range.
  • Fixed checksum and counter for VP70.
  • Fixed issue where removing the network cable would activate system NOK, IO service error and "temperature too high" alarms. 
  • Fixed issue where CODESYS user management files were not included in backup/restore.
  • Fixed issue where linked outputs in CODESYS were hidden in IO configuration.

2.0.8.1

10/02/2025

Corrections

  • Fixed issue that sometimes prevents start-up of controller.

Changes

  • Improved wire break detection handling.

2.0.8.0

17/01/2025

2.0.8.0 based on 2.0.4.1

New features

  • Web Config Tool: Added a Version page with version information of the different software components.
  • Web Config Tool: Added support for PTP time synchronisation.
  • It is now possible to manually disable/enable the USB port  when not in use. (cyber security).
  • EIC: Added Cummins Industrial protocol.
  • EIC: Added Baudouin 6M33 protocol.
  • Added support for DIO2.1 and AIO2.1 plug-in modules.
  • Added device descriptions for 600-series hardware modules for use in CODESYS.
  • Added alarm to indicate unknown traffic on the DEIF network (cyber security).
  • Network port configuration:  New "Standalone" mode to allow CODESYS to be used on Port 0.
  • Added CustomLogic signals to display designer for extra monitoring capabilities.
  • Added iE 7 Display support via Display Port for the iE 250 Base-mounted variant and the iE 350.

Changes

  • Improvements to the IP address settings.
  • Logs: Is is now possible to press Info when the search filter is highlighted.
  • Introduced an alarm to inform users about malfunctioning hardware modules.
  • Introduced an alarm to inform users about configuration issues on hardware modules.
  • Added fuel level as an engine measurement.
  • Increased the persistent storage to 128KB.
  • Upgraded CODESYS runtime version to v3.5.20.40 
  • J1939: Added 40 measurements to analogue output functions.
  • Under frequency detection for NEL can now be specified to a tenth of a percentage point.

Corrections

  • Fixed an issue causing DM2 logs to be empty.
  • Fixed an issue causing display texts not to be translated.
  • Fixed an issue that allowed users to change parameters without logging in.
  • Fixed an issue where custom I/O tests were not shown.
  • Fixed an issue where the DEF level gauge was shown on the dashboard for a Yanmar Stage V engine.
  • Web Config Tool: Fixed an issue causing the user management to stay in edit mode.
  • Web Config Tool: Fixed an issue preventing to write the time settings from the web interface.
  • Fixed issues in user management preventing users from being deleted or having reassigned roles.
  • Fixed an issue causing the status LED to go out of sync.
  • Fixed MIO2.1 device description.
  • Fixed issues with voltage measurement when emulating a split-phase system.
  • Fixed an issue where "System no OK" alarm could occur after changing the time on the controller.
  • Fixed an issue with phase-neutral voltage protections for split- and single-phase AC setups.
  • Fixed an issue in DVC voltage parameters for split-phase.
  • EIC: Fixed an issue causing Stage V lamps for Scania S8 (DEF warning lamp) and Isuzu (Regen warning lamp) not to work.

2.0.4.1

12/07/2024

Initial release of the iE 350 Marine.

The iE 350 Marine, our next-generation controller product line for the maritime segment, features an award-winning design ensuring intuitive and efficient operation. 

The iE 350 Marine exceeds IACS UR E27 cybersecurity regulations, providing robust protection against cyber threats. Engineered for superior performance and reliability, it meets the rigorous demands of modern maritime applications. 

This software package is intended to serve the CORE level functionality.

Minimum required version of PICUS: 1.0.22.0

New features

  • An alarm has been added to inform the customer if the log system on the controller has been damaged or is in any other way malfunctioning. This is done to comply with Computer Security Log Management requirements.
  • Updated Volvo EMS2.4 to support ACM module.
  • Added support for CAT C7.1.
  • EIC: Added support for Kohler KDI3404.

Corrections

  • Fixed default value for the regulator status text.
  • Added support for adjusting the brightness level on the controller.
  • Fixed visibility of ECU and CAN parameters.
  • Fixed issue where Custom Logic was missing.
  • Fixed issue where the licence error alarm could occur after a restore from a backup.
  • Name of Modbus protocols, as seen in PICUS, now includes both type and variant, rather than only type. For example, 'Single Genset GB MB' rather than only 'Single Genset'.
  • Fixed issue where disclaimer was incorrectly shown.

END-USER LICENSE AGREEMENT (“EULA”) FOR DOWNLOADABLE SOFTWARE. (“the SOFTWARE PRODUCT”).

IMPORTANT: PLEASE READ THE TERMS AND CONDITIONS OF THIS LICENSE AGREEMENT CAREFULLY BEFORE CONTINUING WITH THIS PROGRAM INSTALL:

 

DEIF A/S End-User License Agreement ("EULA") is a legal agreement between you (either an individual or a single entity) and DEIF A/S for the DEIF A/S software product(s) identified above which may include associated software components, media, printed materials, and "online" or electronic documentation. By installing, copying, or otherwise using the our product, you agree to be bound by the terms of this EULA. This license agreement represents the entire agreement concerning the program between you and DEIF A/S, (referred to as "licenser"), and it supersedes any prior proposal, representation, or understanding between the parties. If you do not agree to the terms of this EULA, do not install or use the SOFTWARE PRODUCT.

The SOFTWARE PRODUCT is protected by copyright laws and international copyright treaties, as well as other intellectual property laws and treaties. DEIF controllers are licensed, not sold.

1. GRANT OF LICENSE.

The SOFTWARE PRODUCT is licensed as follows:

(a) Installation and Use.
DEIF A/S grants you the right to install and use copies of the SOFTWARE PRODUCT on your computer running a validly licensed copy of the operating system for which the SOFTWARE PRODUCT was designed Windows 7, Windows 8, Windows 10.

(b) Backup Copies.
You may also make copies of the SOFTWARE PRODUCT as may be necessary for backup and archival purposes.

2. DESCRIPTION OF OTHER RIGHTS AND LIMITATIONS.

(a) Maintenance of Copyright Notices.
You must not remove or alter any copyright notices on any and all copies of the SOFTWARE PRODUCT.

(b) Prohibition on Reverse Engineering, Decompilation, and Disassembly.
You may not reverse engineer, decompile, or disassemble the SOFTWARE PRODUCT, except and only to the extent that such activity is expressly permitted by applicable law notwithstanding this limitation.

(c) Rental.
You may not rent, lease, or lend the SOFTWARE PRODUCT.

(d) Compliance with Applicable Laws.
You must comply with all applicable laws regarding use of the SOFTWARE PRODUCT.

3. TERMINATION

Without prejudice to any other rights, DEIF A/S may terminate this EULA if you fail to comply with the terms and conditions of this EULA. In such event, you must destroy all copies of the SOFTWARE PRODUCT in your possession.

4. COPYRIGHT

All title, including but not limited to copyrights, in and to the SOFTWARE PRODUCT and any copies thereof are owned by DEIF A/S or its suppliers. All title and intellectual property rights in and to the content which may be accessed through use of the SOFTWARE PRODUCT is the property of the respective content owner and may be protected by applicable copyright or other intellectual property laws and treaties. This EULA grants you no rights to use such content. All rights not expressly granted are reserved by DEIF A/S.

5. NO WARRANTIES

DEIF A/S expressly disclaims any warranty for the SOFTWARE PRODUCT. The SOFTWARE PRODUCT is provided 'As Is' without any express or implied warranty of any kind, including but not limited to any warranties of merchantability, noninfringement, or fitness of a particular purpose. DEIF A/S does not warrant or assume responsibility for the accuracy or completeness of any information, text, graphics, links or other items contained within the SOFTWARE PRODUCT. DEIF A/S makes no warranties respecting any harm that may be caused by the transmission of a computer virus, worm, time bomb, logic bomb, or other such computer program. DEIF A/S further expressly disclaims any warranty or representation to Authorized Users or to any third party.

6. LIMITATION OF LIABILITY

In no event shall DEIF A/S be liable for any damages (including, without limitation, lost profits, business interruption, or lost information) rising out of 'Authorized Users' use of or inability to use the SOFTWARE PRODUCT, even if DEIF A/S has been advised of the possibility of such damages. In no event will DEIF A/S be liable for loss of data or for indirect, special, incidental, consequential (including lost profit), or other damages based in contract, tort or otherwise. DEIF A/S shall have no liability with respect to the content of the SOFTWARE PRODUCT or any part thereof, including but not limited to errors or omissions contained therein, libel, infringements of rights of publicity, privacy, trademark rights, business interruption, personal injury, loss of privacy, moral rights or the disclosure of confidential information.