iE 350 Application SW (Flexible application)

You’re about to download iE 350 Application SW (Flexible application)

You have chosen to download our software.

Within a few seconds, you will receive an email containing a download link.

Having trouble using the software? Please contact support@deif.com. 

Best regards, 

DEIF A/S

The software is subject to copyright DEIF A/S
By following the above mentioned link and downloading the file you automatically accept DEIF A/S copyright and license agreement (EULA). The license agreement can be found on www.deif.com/software

This software applies to the following DEIF products:

You’re about to download 2.0.9.1

The main changes implemented since the last version are as follows:

2.0.9.1 based on 2.0.9.0

Corrections:

  • Fixed issue where external and redundant breaker feedback could result in an incorrect breaker position state
Ver. Date Description

2.0.9.1

13/06/2025

2.0.9.1 based on 2.0.9.0

Corrections:

  • Fixed issue where external and redundant breaker feedback could result in an incorrect breaker position state

2.0.9.0

04/05/2025

2.0.9.0 based on 2.0.8.1

New features

  • Three pump logic routines can now be set up to control the pumping of a substance.
  • Implement ECU diagnostic to enable run coil and ECU power while the engine is stopped.
  • All configuration dependent values are now possible to use in the flexible Modbus.  
    e.g. power supply measurements (dependent on hardware and number of extension racks) can now be mapped to Modbus.
  • Up to 10 ACM3.1 cards allowed in one controller to be used for measurement (preview feature).

Changes

  • EIC: Volvo Penta EMS2.4: "Engine Override Control Mode" changed to "Speed control".  
  • EIC: Volvo Penta EMS2.4: TSC1 will not be transmitted if VP70 is used for regulation. 
  • Modbus timeout increased from 10 sec to 100 sec on iE 250 and iE 350.  
  • Number of possible Modbus connections changed from 20 to 100 on iE 250 and iE 350
  • Added write permission for "Priorities" when controller is in emulation.

Corrections

  • Fixed issue where changes made in the UI were not registered.
  • Fixed issue where the "IO configuration" menu would show empty slots.
  • Fixed issue where tree-structure menu groups could not be collapsed using touch.
  • Fixed issue where configuring a Modbus value to "true" made the value "255" instead of "1".
  • Fixed issue where measurements from multiple ECUs were not shown in UI for e.g. configuring alarms.
  • Fixed issue where display user could not clear DM2 logs.
  • Fixed issue where iE controller could not start without MIO module. 
  • Fixed issue with missing alarm icons.
  • Fixed issue where user could enter parameter values outside of valid range.  
  • Fixed checksum and counter for VP70.
  • Fixed issue where removing network cable would activate system NOK, IO service error and "temperature too high" alarms. 
  • Fixed issue where CODESYS user management files were not included in the backup/restore.
  • Fixed issue where linked outputs in CODESYS was hidden in IO configuration.
  • Fixed issue where the Genset was not de-loading correctly when it was connected to the Mains.
  • Fixed issue where BUS TIE breaker could not de-load and open a ring connected busbar.

2.0.8.0

21/01/2025

2.0.8.0 based on 2.0.6.0

New features

  • Web Config Tool: Added a Version page with version information of the different software components.
  • Web Config Tool: Added support for PTP time synchronisation.
  • It is now possible to manually disable/enable the USB port  when not in use. (cyber security).
  • EIC: Added Cummins Industrial protocol.
  • EIC: Added Baudouin 6M33 protocol.
  • Added support for DIO2.1 and AIO2.1 plug-in modules.
  • Added device descriptions for 600-series hardware modules for use in CODESYS.
  • Added alarm to indicate unknown traffic on the DEIF network (cyber security).
  • Network port configuration:  New "Standalone" mode to allow CODESYS to be used on Port 0.
  • Added CustomLogic signals to display designer for extra monitoring capabilities.
  • Added iE 7 Display support via Display Port for the iE 250 Base-mounted variant and the iE 350.

Changes

  • Improvements to the IP address settings.
  • Logs: Is is now possible to press Info when the search filter is highlighted.
  • Introduced an alarm to inform users about malfunctioning hardware modules.
  • Introduced an alarm to inform users about configuration issues on hardware modules.
  • Added fuel level as an engine measurement.
  • Increased the persistent storage to 128KB.
  • Upgraded CODESYS runtime version to v3.5.20.40. 
  • J1939: Added 40 measurements to analogue output functions.
  • Under frequency detection for NEL can now be specified to a tenth of a percentage point.

Corrections

  • Fixed an issue causing DM2 logs to be empty.
  • Fixed an issue causing display texts not to be translated.
  • Fixed an issue that allowed users to change parameters without logging in.
  • Fixed an issue where custom I/O tests were not shown.
  • Fixed an issue where the DEF level gauge was shown on the dashboard for a Yanmar Stage V engine.
  • Web Config Tool: Fixed an issue causing the user management to stay in edit mode.
  • Web Config Tool: Fixed an issue preventing to write the time settings from the web interface.
  • Fixed issues in user management preventing users from being deleted or having reassigned roles.
  • Fixed an issue causing the status LED to go out of sync.
  • Fixed MIO2.1 device description.
  • Fixed issues with voltage measurement when emulating a split-phase system.
  • Fixed an issue where "System no OK" alarm could occur after changing the time on the controller.
  • Fixed an issue with phase-neutral voltage protections for split- and single-phase AC setups.
  • Fixed an issue in DVC voltage parameters for split-phase.
  • EIC: Fixed an issue causing Stage V lamps for Scania S8 (DEF warning lamp) and Isuzu (Regen warning lamp) not to work.