Combination power management - Greenfield
In combination applications, the system incorporates features and functionalities of both our off-grid and grid-tied technology, automatically adjusting power and reactive power references with grid support if frequency or voltage drops, or rotating the genset to automatically ensure the most fuel-optimised running mode through various load demands.
Supporting fuel-saving in grid-tied operations, all gensets can be stopped to maximise the penetration from sustainable sources. Automatic changeovers between grid-tied and off-grid in case of mains failure are possible, even during operation. The system provides an effective Power Management solution for plants with multiple sustainable or fossil, fueled power sources.
Click on the green dots to learn more about our products
AGC 150 Mains
The AGC 150 Mains controller can synchronise one or two breakers (mains breaker and tie breaker) plus protect and monitor the utility.
AGC-4 Mk II
The automatic genset controller AGC-4 Mk II is the world’s most comprehensive genset controller offering all necessary functions for protection and control
ASC 150 Solar
The ASC 150 Solar provides effective, flexible, and scalable photovoltaic (PV) inverter control with a wide range of options for greenfield and brownfield hybrid power applications.
ASC-4 Solar
Ideally suited for greenfield hybrid power plants, the ASC-4 Solar controller can interface with other DEIF controllers and a wide range of PV inverters, enabling you to integrate solar power in greenfield applications and maximise sustainable power penetration.
ASC 150 Storage
The ASC 150 Storage provides effective, flexible, and scalable energy storage system (ESS) control with a wide range of options for greenfield and brownfield hybrid power applications.
It can be used on its own for ESS/hybrid rental or integrated in third-party plant control solutions or a DEIF power management system.
The controller optimises the battery power, to save fuel and maximise green penetration.
ASC-4 Battery
The ASC-4 Battery lets you quickly and easily add energy storage systems (ESS) such as batteries in greenfield hybrid applications with other DEIF controllers, providing seamless energy storage in commercial and industrial applications.
AGC 150 Generator
The AGC 150 Genset controller containing all necessary functions for control and protection of a genset. The slim design makes the genset controller suitable for paralleling even small gensets thus the AGC 150 is integrable in nearly all types of gensets.
AGC-4 Mk II
The automatic genset controller AGC-4 Mk II is the world’s most comprehensive genset controller offering all necessary functions for protection and control
-
Contact us to discuss your options
- 90 years of energy pioneering
- Manufactured at the highest standards
- Superior quality
- Unmatched service and support
- Made in Denmark
Advanced Genset Controller AGC 150 Mains
AGC 150 Mains - features
Operating modes with single or multiple mains:
AMF, Fixed power, Mains power export Load take over, Peak shaving
- Mains (Utility)
- power monitoring (kW, kV, A & pf)
- decoupling protection
- kW export protection
- electrical protections
- No break transfer of load
- Multi start settings
- Minimum of starting genset
- 12 Digital inputs and 12 digital outputs
- Communications ports (CAN, USB, RS485, Ethernet).
- Event & Alarm log (500 each)
- Programmable PLC editor
Flexible PV controller ASC 150 Solar
Single controller
- Useful for brownfield applications
- Makes sure that there is a minimum genset load
- Optimises the diesel genset load for high efficiency and low carbon footprint
Power management
- Automatically maximises PV power
- Automatically Load-dependent start and stop generators
- Automatically closes and opens breakers
- Optimises the diesel genset load for high efficiency and low carbon footprint
- Balances the loads in the system
Off-grid applications
- With a genset:
The controller uses the genset power measurements to calculate the set points for the PV power.
- With storage:
The controller combines the available PV power with the charge/discharge scheme to determine the set point for the PV power.
Grid-tied applications
- Feed surplus PV energy to the grid
- Charge the energy storage system (ESS)
- Regulate PV production to match the self-consumption
Flexible ESS controller ASC 150 Storage
Single controller:
- Useful for rental and brownfield applications
- Automatically charges and discharges the ESS
- Optimises the diesel genset load for high efficiency and low carbon footprint
- Requires power measurement and breaker feedback for other power sources
- Only one source: Can use the controller's 4th current measurement.
- Multiple power sources: Measurements from:
- Genset controllers (DEIF or third parties)
- Power meters
- Transducers -
Power management communication is not required
Power management:
- Automatically charges and discharges the ESS
- Automatically uses the ESS as spinning reserve for PV and microgrids
- Automatically starts and stops generators
- Automatically closes and opens breakers
- Optimises the diesel genset load for high efficiency and low carbon footprint
- Optimises the fuel consumption
- Balances the loads in the system
- Uses the plant logic
- Makes sure that the system is safe
Automatic Sustainable Controller ASC-4 Battery
- Solar, storage, wind, Mains and genset integration in hybrid applications
- ASC-4 sustainable controllers and AGC-4 Mk II/AGC 150 let you control up to 32 gensets
- Applications with up to 16 sustainable power plants
- Simple graphical configuration
- Communicates with BCU, BMS, or PCS over Modbus
- Charging/discharging based on SOC or Schedular Command timers
- Optimal genset load constraint
- Define and change priority of connected power sources
- Controls functions, energy source or power source
- Grid-forming, grid-following, or droop mode (virtual synchronous generator)
- Uptime guaranteed through spinning reserve
- Maximised sustainable power penetration
- Load dependent genset start/stop by PMS or DO
- SOC dependent genset start/stop by DO - Rental
- Minimum genset load constraint
- Ideal for self-consumption applications
- Highly customisable with user-friendly M-Logic tool
- Control of breaker
- Record time commissioning with DEIF Emulation
- uses and verifies the functions of the real system for test, production and design - Suitable for power management solutions fitted with AGC-4, AGC 150 or AGC 200 genset controllers
- Suitable for stand-alone solutions using multi-instruments such as DEIF’s MIB or MIC
Automatic sustainable controller ASC-4 Solar
- Solar, storage, wind, Mains and genset integration in hybrid applications
- ASC-4 sustainable controllers and AGC-4 Mk II/AGC 150 let you control up to 32 gensets
- Simple graphical configuration
- Uptime guaranteed through spinning reserve
- Maximised sustainable power penetration
- Load dependent genset start/stop
- Minimum genset load constraint
- Ideal for self-consumption applications
- Highly customisable with user-friendly M-Logic tool
- Control of breaker
- Record time commissioning with DEIF Emulation
- uses and verifies the functions of the real system for test, production and design - Suitable for power management solutions fitted with AGC-4, AGC 150 or AGC 200 genset controllers
- Suitable for stand-alone solutions using multi-instruments such as DEIF’s MIB or MIC
Automatic genset controller AGC-4 Mk II
- Automatic Mains Failure sequence
- Multi-master Power Management
- Power Management Core (32dg)
- Power Management Extended (>32dg)
- RMB Transformer maintenance with up to 32 gensets
- PLC logic
- Engine CANbus
- Din rail mount
- Flexible Hardware
- Additional CANbus based I/O (9 x CIO modules)
- Redundant controller
- Redundant CANbus for Power mamangement
- N+X configuration
- Close Before Excitation / Run-up synchronization from 6 seconds
- DEIF digital AVR DVC550 support
- Multi purpose PID´s
- Gridcode compliant with: VDE AR-N 4110/4105 (Medium voltage, Germany, VDE AR-N 4105 (low voltage, Germany, EN 50549-1:2019 (Europe), ENA EREC G99 (United Kingdom)
- Touch Screen Support (TDU107)
- Tier4 final/stage5
- Emulation for easy training and FAT
- Hybrid EMS support (via ASC-4)
- Heavy consumer (via ALC-4)
- Fuel optimisation
- Fully compatible with AGC 150 and ASC-4
- TÜV pending and UL approved
Advanced graphical interface AGI 400
- Wide screen format
- True glass front
- Capacitive touch screen
- Multi-touch and Gestures
- Robust aluminium housing
- SD card slot for easy storage and updating
- USB hosts for printers, accessories, data storage and updating
- Dimmable LED backlight
- Web server for remote access from i.e. mobile devices
- 3 Ethernet ports with integrated switch
- Serial communication (RS-232, RS-422 and RS-485)
- Wide range of support for industrial protocols
- OPC UA Server and Client
- JAVA scripting
- CODESYS V3 (optional)
- Powerful ARM Cortex-A9 processor
- Plug-in module for CANbus (CANopen/J1939)
- Wide operating temperature -20°C to +60°C
- Marine certifications
- Certified for hazardous environments
- Available in 7", 10", 15" and 21" sizes
