Waiting list Online

Training AGC - 06/2022 Designer Level

This training course is for designers who require detailed knowledge of the DEIF controller’s capabilities to be able to design and configure advanced power management systems.

Where: Online

When: 22-06-2022 - 23-06-2022

Price: 850 EURO

Register

What will you learn?

  • You will learn to setup a power management system with multiple mains and BTB’s.
  • You will learn which options of the controller to integrate into an application and how to design a switchboard for DEIF controllers.
  • You will be able to troubleshoot advanced power management systems and recognize different plant modes
  • You will learn to program custom AGC logic

Meet the DEIF instructors

Learn more about the experts behind the our courses. Each DEIF instructor has a one or more products in which they are specialised.

Read about the instructors here

AGC Designer level

This training course is for designers who require detailed knowledge of the DEIF controller’s capabilities to be able to design and configure advanced power management systems. 

This is a two-day training course within Danish working hours 8.30 am to 4.00 pm

Course prerequisites

The AGC Designer training session presupposes completion of the AGC Service. Attending both levels of AGC training will give you an in-depth gradual learning scale that enables you to fully master the sophisticated features of your power management system.

Please note that the training will be conducted in English and that you have to bring a laptop with a LAN port. You will have to install software on your PC, so please check if it requires special permission from your IT-administrator.

Cancellation

In the event of cancellation up to 14 days prior – no charge will be made. If cancellation is made after this time then an administration fee of 250 EUR per person will apply.
DEIF reserves the right to cancel a training course with 2 weeks’ notice if the number of participants is insufficient.

Agenda

Day 1 - 22nd of June

08:30 - Introduction
08:35 - AGC DE Module 1 (Product knowledge, the procedure, applications)
10:00 - Break
10:15 - AGC DE module 1 (Exercise DE 1, specifications, exercise DE 2, interfacing / installation)
12:00 - Lunch break
12:45 - AGC DE Module 2 (Tiebreaker advantages, exercise DE 3)
13:45 - Break
14:00 - AGC DE Module 2 (ID to run / Runtype, exercise 4, autoswitch, exercise 5)
16:15 - Evaluation of the day

Day 2 - 23rd of June

08:30 - AGC DE Module 3 (M logic, exercise 6, general purpose PID’s, derate, idle run)
10:00 - Break
10:15 - AGC DE Module 3 (Engine heater, ventilation, battery test, fan logic, double starter, ground relay, differential measurements)
12:00 - Lunch
12:30 - AGC DE Module 4 (Mains ATS, exercise 7, available power alarm, exercise 8)
14:00 - Break
14:15 - AGC DE Module 4 (Fuel pump logic, asymmetric loadshare, exercise 9-10-11, N+X, command timers, warmup ramp, exercise 12-13-14)
16:15 - Evaluation of the training course

DEIF Skive

Training is a cornerstone to success

With the rapid advances in generator control and the increasingly sophisticated communication between engines themselves, it has become more necessary than ever for operators and service personnel to receive hands-on training.

DEIF commits to providing our customers with the information and resources necessary for the efficient use of our products. To that end, we offer training sessions for you and your associates to help you learn how to use DEIF generator controllers and software appropriately on our simulation equipment around the world. Attending a DEIF training session will enable you to provide your customers with cost-efficient solutions that meet all common requirements.  

We believe in learning by doing. Thus our courses involve hands-on training with simulation and emulation equipment in a clean, hazard-free, and controlled environment. Together we will simulate and troubleshoot a wide range of typical fault conditions and also applications based on input from the course participants without risking damage to your plant. The sessions are carried out in small groups for greater flexibility and more involvement.

Can I help you?

Hst 2

Helle Holmgaard

Senior Event Manager

+45 4070 9670 |

Training AGC - 06/2022

Designer Level
22-06-2022 - 23-06-2022
Online
850 EURO
Waiting list

Register

Complete the form below to sign up for the course