Almost full

PPU 300 11/2022 Operator & Service Level

This training course is for operators and service technicians. You will learn the basic functions of the PPU 300 controller and how to carry out daily routine operations.

Where: Skive, Denmark

When: 08-11-2022 - 09-11-2022

Price: 850 EURO

Register

What will you learn?

  • You will learn the basic menu functions of the genset controller and become acquainted with the menu structure
  • You will learn how to use the controller and obtain in-depth knowledge of the functionality it offers.
  • You will learn how to use the different configuration inputs, modes of operation and how to change protection settings.
  • You will learn how to connect the utility software, configure I/O’s, parameter settings etc.

Meet the DEIF instructors

Learn more about the experts behind the our courses. Each DEIF instructor has a one or more products in which they are specialised.

Read about the instructors here

PPU 300 Service level

This training course is for operators and service technicians. You will learn the basic functions of the PPU 300 controller and how to carry out daily routine operations When familiar with the primary functions you will proceed with more advanced tasks such as setting up, troubleshooting and commissioning typical genset applications. 

This is a two-day training course within Danish working hours 8.30 am to 4.00 pm

Course prerequisites

Attending the PPU 300 CODESYS training session requires completion of the PPU 300 Service course.

Professional hands-on training at DEIF

Cancellation

In the event of cancellation up to 14 days prior – no charge will be made. If cancellation is made after this time then an administration fee of 250 EUR per person will apply.
DEIF reserves the right to cancel a training course with 2 weeks’ notice if the number of participants is insufficient.

Agenda

Day 1 - 08th of November
08:30 - 08:45 Welcome introduction to DEIF
08:45 - 09:45 PPU 300 introduction - DEIF website introduction
09:45 - 10:00 Break
10:00 - 11:00 Display (LED’s & buttons, Menu structure, Hands-on task 1 – Navigating in display)
11:00 - 11:10 Break
11:10 - 12:00 Synchronization and regulation (Synchronization methods, Regulator modes, Intro to test switchboard , Hands-on task 2 – Operate system in Local operation)
12:00 - 12-45 Lunch
12:45 - 14:15 Alarm handling( Hands-on task 3 – Alarm handling)
14:15-14:30 Break
14:30-15:30 PICUS introduction (Hands-on task 4 – Make backup and update software)
15:30 - 16:00 - Questions

Day 2 - 09th of November
08:30 - 09:00 PICUS – Going through utility software
09:00 - 09:40 Hands-on task 1 – Make the single line drawing
09:40 - 09:50 Break
09:50 - 10:15 Hands-on task 2 - Setup control inputs
10:15 - 11:00 Hands-on task 3 - Operate system in Remote operation.
11:00 - 11:15 Hands-on task 4 – Test the dead-bus closing function
11:15 - 11:25 Break
11:25 - 12:05 Hands-on task 5 – Analogue regulation
12:05 - 12:50 Lunch
12:50 - 13:35 Hands-on task 6 – Custom Logic
13:35 - 13:45 Hands-on task 7 – Operate PPU using Modbus
13:45 - 13:55 Break
13:55 - 14:35 Continue task 7
14:35 - 15:20 Hands-on task 8 – Setup an analogue input 
15:20 - 15:30 Break 
15:30 - 16:00 Questions 

 

 

 

 

 

deif hq

Training is a cornerstone to success

With the rapid advances in generator control and the increasingly sophisticated communication between engines themselves, it has become more necessary than ever for operators and service personnel to receive hands-on training.

DEIF commits to providing our customers with the information and resources necessary for the efficient use of our products. To that end, we offer training sessions for you and your associates to help you learn how to use DEIF generator controllers and software appropriately on our simulation equipment around the world. Attending a DEIF training session will enable you to provide your customers with cost-efficient solutions that meet all common requirements.  

We believe in learning by doing. Thus our courses involve hands-on training with simulation and emulation equipment in a clean, hazard-free, and controlled environment. Together we will simulate and troubleshoot a wide range of typical fault conditions and also applications based on input from the course participants without risking damage to your plant.

The sessions are carried out in small groups for greater flexibility and more involvement.

Travelling to Skive

DEIF A/S is located in Skive, a 30 minute drive from Karup Airport, and 10 minutes’ drive from the below hotels. We will be happy to assist with hotel reservations. If you choose to make your own reservation, please refer to DEIF to obtain the below corporate rates.

Hotel Strandtangen
Located at the harbour
Reservations: (+45) 9676 0800

Hotel Gl. Skivehus
Located in the center of Skive
Reservations: (+45) 9752 1144

SUP Ellen Og Asmus (3) 1200Px

Copyright Skive Kommune

Can I help you?

Hst 2

Helle Holmgaard

Senior Event Manager

+45 4070 9670 |
Almost full

PPU 300 11/2022

Operator & Service Level
08-11-2022 - 09-11-2022
Skive, Denmark
850 EURO
Available

Register

Complete the form below to sign up for the course