Multi-line 2 EC-1/GC-1 Application Software Std. Lang. Package series 1.x.

This software applies to the following DEIF products:

You’re about to download 1.43.4

The main changes implemented since the last version are as follows:

This software applies to the following DEIF products:

  • Multi-line 2 - EC-1/GC-1

Changes:

  • Status of cable supervision in USW optimised

Ver. Date Description

1.43.4

08/10/2010

This software applies to the following DEIF products:

  • Multi-line 2 - EC-1/GC-1

Changes:

  • Status of cable supervision in USW optimised

1.43.3

18/08/2009

  • Wire break symbol in Chinese added.

1.43.2

18/06/2008

  • Binary inputs with cable supervision updated.

1.43.1

04/02/2008

  • Energy counter updated.

1.43.0

15/01/2008

  • Multi input wirebreak failclass changed to warning

1.42.3

02/11/2007

  • Multiinput wirebreak alarm updated.

1.42.2

22/06/2007

  • SW version number corrected.

1.42.1

19/06/2007

  • Extended stop updated when using frequency as running feedback.
  • Remote puls start updated during cooldown

1.42.0

14/05/2007

New features:

  • New digital input function, remote puls start
  • New digital input function, remote puls stop
  • New relay output function, auto mode indication

Changes:

  • Mode (Auto/Local) is not stored, if power is removed from the controller.

1.41.2

28/02/2007

  • Busbar transformer setting updated.

1.41.1

19/02/2007

Changes:

  • Engine running relay now reacts to running feedback.
  • Ext stop is now performed when running feedback is lost.
  • Failclass error corrected in Hz / V failure alarm

1.41.0

03/01/2007

Changes:

  • Shutdown possibility during start sequence added
  • 4-20 mA input range improved.

1.40.4

01/10/2006

Changes:

  • MB open / close feedback updated

1.40.3

22/08/2006

Changes:

  • Chinese texts updated.
  • Icons updated.
  • CanOpen remote start/stop updated.
  • Firepump updated with CAN alarm.
  • Alarm relay B updated.
  • Low power readout for USW scaled.
  • Oilpressure readout for USW scaled.
  • PF calculation updated.

1.40.2

21/03/2006

Changes:

  • L1-0 error message updated

1.40.1

08/03/2006

Changes:

  • Running hour counter updated.
  • MB handling upon power up changed

1.40.0

08/02/2006

New features:

  • VDO 3 range increased to 2400 ohm.
  • External heater function added.
  • New stop coil function added - stop coil no start
  • L1-N value error alarm added.
  • Mains failure frequency detection ON/OFF function added.
  • Additional view added.
  • Parameter groups added.
  • GC-1 frequency readings shown with 1 decimal.
  • Power readings shown with 1 decimal if Pnom < 49kW.
  • Diode compensation function added.
  • Test input added for AMF.
  • New digital input texts added.
  • New text "Coolant pressure" added to analog input (4-20mA).
  • External trip of MB added to AMF sequences.
  • Extra password level added.
  • GB breaker delay function added.
  • Oilpressure feedback added.

Changes:

  • Some parameter settings updated.

1.30.5

29/11/2005

New features:

  • New AMF situations added.
  • Run status alarm added.

Changes:

  • Fuel pump function updated.
  • Stop coil funciton updated.
  • Input functions updated (Idle run, firepump).
  • Alarm / limit relay functions updated.
  • Default settings updated (Charger gen).
  • Breaker interlock updated.
  • Start enable updated.
  • Parameter menu updated.
  • Setting of voltage transformers updated.
  • Language handling updated.
  • AMF functions updated.
  • VDO user definable inputs updated.
  • Run enable updated.
  • Block (shutdown) updated.
  • HW change to VDO inputs supported.
  • Device number for options in USW updated.

1.30.2

21/10/2005

Changes:

  • Tacho feedback updated
  • E counter updated

1.30.1

05/10/2005

Changes:

  • Test function updated.

1.30.0

05/10/2005

New features:

  • Italian and Chinese language supported.
  • Option H1 (CANopen) added.
  • 1 second delay added to starter and tacho feedback

Changes:

  • Writing of outputs from USW corrected.
  • Cool down timer updated remote mode.

1.21.0

12/09/2005

New features:

  • German, Spanish and French language supported.

Changes:

  • Nominal voltage is phase-phase
  • D+ timer updated
  • Firepump updated
  • "f/U..." texts changed

1.20.1

12/09/2005

Changes:

  • Test function updated

1.20.0

03/08/2005

New features:

  • Support for 3-phase measurementboard (GC-1)
  • Support for option B3 (GC-1 AMF)

1.10.2

04/07/2005

Changes:

  • Configurable outputs updated

On this page, you can download software updates for your product(s) and help yourself to various utility tools and add-ons that will assist you in setting up, detecting faults and configuring your product(s).

Please be advised that not all of our products can be updated by the user. Nor do all of our products come with a utility tool. Consequently, the list on this page cannot be considered an overview of our product programme.

DEIF will register your download along with the used e-mail address for the purpose of sending out information on future updates, if requested.

DEIF cannot be made responsible for any consequences of failed product updates or use of utility tools. Nor can DEIF A/S be made responsible for consequences of changes in behaviour of products due to a software upgrade. It is always the responsibility of the user to ensure correct set-up and configuration before commissioning. Please study the version log of the software before updating the product.

Licence agreement for software downloaded from www.deif.com

Downloaded software remains the property of DEIF. The software may not be distributed for commercial purposes, changed or reused in full or in part or sold to any third parties.

The latest versions for full functionality

As always, we recommend that you install our offered improvements to fully utilise your DEIF product.

All improved software can be downloaded at your convenience at www.deif.com under “Software”.

Should you have any questions or experience problems finding the relevant software for your product, please feel free to call DEIF A/S at +45 96149614 or your relevant local DEIF office. Alternatively, we are always ready to assist you, if you send an e-mail to support@deif.com.

Press release, June 2015

Information on product improvement specifically related to “older” DEIF A/S ML-2 products.